- Manuals
- Brands
- Voxx Manuals
- Car Video System
- Movies2Go MTG10UHD
- Installation manual
10.1” /13.3” overhead lcd monitor with built-in dvd player
Hide thumbs
-
- Contents
- Table of Contents
- Troubleshooting
- Bookmarks
Table of Contents
-
Important Notices
-
Table of Contents
-
Materials Include in this Package
-
Installing the Unit in a Vehicle
-
Installing the Snap-On Shroud
-
Installing the Snap-On Screen Cover
-
Installing the Trim Ring
-
General Vehicle Installation Approach
-
Vehicle Preparation
-
Connecting the Dome Lights
-
Installing the Mounting Bracket
-
Installing the Unit Video System-Wiring Diagram
-
Installing the Unit Video System-Mounting the Unit
-
Appendix A - Removing the Screen Back Cover
-
Appendix A - Removing the Trim Ring and Shroud
-
Appendix B - Installing the Optional Thick Trim Ring
-
Appendix C - Installing the Optional Smartstream Module (WM1)
-
Troubleshooting
Advertisem*nt
Quick Links
- 1 Materials Include in this Package
- 2 Installing the Unit in a Vehicle
- 3 Installing the Unit Video System-Wiring Diagram
- 4 Appendix C - Installing the Optional Smartstream Module (Wm1)
- 5 Troubleshooting
- Download this manual
MTG10UHD/MTG13UHD
10.1" /13.3" Overhead LCD Monitor
With Built-In DVD Player
Installation Guide
Table ofContents
Advertisem*nt
Table of Contents
Related Manuals for Voxx Movies2Go MTG10UHD
-
Car Video System Voxx Movies To Go MTG10UHD Owner's Manual
10.1"/13.3" overhead lcd monitor with built-in dvd player (36 pages)
-
Car Video System VOXX HR7012S Owner's Manual
Rear seat video headrest system (47 pages)
-
Car Video System VOXX Invision HR8D Owner's Manual
Rear seat video headrest system (36 pages)
-
Car Video System Voxx HR8D Owner's Manual
Rear seat video headrest system (51 pages)
-
Car Video System Voxx avxmtghr9hd Installation And Operation Manual
9” lcd monitorwith built-in dvd playerand hdmi/mhl portfor rear seat entertainment (32 pages)
Summary of Contents for Voxx Movies2Go MTG10UHD
- Page 1 MTG10UHD/MTG13UHD 10.1” /13.3” Overhead LCD Monitor With Built-In DVD Player Installation Guide...
-
Page 3: Important Notices
Important Notices Installation of overhead products requires careful planning and preparation. Be extremely careful when working on a vehicle with side curtain air bags. Do not route wires near any portion of the side curtain air bag assemblies. This includes any anchor points in A, B, C or D pillars of the vehicle. - Page 4 For safety reasons, when changing video media, it is recommended that the vehicle is not in motion, and that you do not allow children to unfasten seat belts to change video media or make any adjustments to the system. System adjustments can be accomplished using the remote control, while seat belts remain fastened.
-
Page 5: Table Of Contents
Table Of Contents Materials Include In This Package .............6 Installing The Unit In A Vehicle ..............8 Installing The Snap-On Shroud ..............9 Installing The Snap-On Screen Cover ............10 Installing The Trim Ring ................11 General Vehicle Installation Approach ..........12 Vehicle Preparation ..................13 Connecting The Dome Lights ..............14 Installing The Mounting Bracket .............16 Installing The Unit Video System- Wiring Diagram ......17... -
Page 6: Materials Include In This Package
Materials Included In This Package 1. 10.1” / 13.3” TFT LCD Overhead Monitor with DVD Player - (1 pc) 2. Hardware Package (P/N 540-017) - (1 pkg) M3 x 5mm Phillips Screws - (12 pcs) #8 x 3/8” Self Drilling Screws - (4 pcs) (*NOTE: For Installation of WM1x4pcs) M5 x 10mm Phillips Screws... - Page 7 Materials Included In This Package 3. Remote Control w/ Battery (P/N 500-003) - (1 pc) 4. For 10.1”-Mounting Bracket (P/N 201-413) - (1 pc) 13.3”-Mounting Bracket (P/N 201-414) - (1 pc) 5. 6 Pin Power/Dome Light Harness (P/N 112-4270) - (1 pc) 6.
-
Page 8: Installing The Unit In A Vehicle
Installing the Unit In A Vehicle Tools Required #2 Phillips Screwdriver #1 Phillips Screwdriver Utility or Razor Knife Wire Strippers Upholstery hook tool (for removal of panels as necessary) Electrical Tape Masking Tape Multimeter to verify 12 volt DC and continuity (Do not use a test light or logic probe) Marker pen –... -
Page 9: Installing The Snap-On Shroud
Installing the snap-on shroud Installing the Shroud *NOTE: Work on a soft surface to avoid damaging the plastic. 1. Remove the double sided tape backing from the two strips on the center section of the shroud. 2. Hook the shroud over the dome light and align the shroud tabs (1)with the eight openings around the rim of DVD player(2 ). -
Page 10: Installing The Snap-On Screen Cover
Installing the Snap-On Screen Cover Installing the Screen Cover 1. Open the LCD screen. 2. Hook the two tabs “A” (as shown) on the bottom edge of the screen. 3. Carefully snap the opposite side over the hinge. NOTE: If the wrong color Shroud and Screen Cover is installed, refer to Appendix A of this manual for instructions to change the Shroud and Screen Cover color. -
Page 11: Installing The Trim Ring
Installing the Trim Ring The trim ring is attached to the video monitor using the perimeter screw bosses. It is important that the screws used in this installation are not over tightened, and that the video monitor and trim ring are mounted in such a way that the assembly does not distort (or bend) when the mounting screws are tightened. -
Page 12: General Vehicle Installation Approach
General Vehicle Installation Approach 1. Decide upon system configuration and configuration and peripheral options that will be installed (ie...External Video Gaming System). 2. Review all manuals to become familiar with electrical requirements and connections. 3. Decide upon mounting locations of all components and method of mounting. 4. -
Page 13: Vehicle Preparation
Vehicle Preparation 1. Locate an accessory +12v power source with a good ground. These wires can be found at the ignition switch or fuse-box. Power Source • +12v when the key is in the ACC and run positions. • 0v when the key is OFF. NOTE: Always fuse the ACC +12V at the source where it is connected to the vehicle. -
Page 14: Connecting The Dome Lights
Connecting the Dome Lights The dome lights in the video monitor require three connections to the vehicle’s wiring. There are two common types of dome light circuits used, positive switched systems or negative switched systems. Positive switched systems supply voltage to the interior lights to turn ON;... - Page 15 Connecting the Dome Lights Positive Switched Dome Lighting Negative Switch Red/Black-Lamp on To 3 pin Red/Black-Lamp ON To 3 pin Black/Red-Lamp com constant connector connector Black/Red-Lamp Common Purple/Brown-Lamp A +12 VDC on Monitor Purple/Brown-Lamp Auto Fused Factory Dome Light Circuit constant +12 VDC Factory Door Ajar...
-
Page 16: Installing The Mounting Bracket
Installing the Mounting Bracket Installing the Mounting Bracket 1. Once all the pre-wiring is complete, locate: • Mounting Bracket • (4) #8 x 3/8” Self-Drilling Screws 2. Carefully align the Mounting Bracket in the location it is to be installed with direction arrow facing the front of the vehicle (make sure there is nothing between the Mounting Bracket and Roof Cross-Member). -
Page 17: Installing The Unit Video System-Wiring Diagram
Installing the Unit Video System-Wiring Diagram Connect the 6 pin harness to the unit and make the connections to the vehicle. Connect the red and black power wires of the Power Harness to vehicle’s electrical system by connecting into an accessory hot line and a good ground.Soldering all power connection is the suggested technique that should be used to ensure a problem free connection. - Page 18 Installing the Unit Video System-Wiring Diagram Wiring Diagram WM1(Optional) RF OUTPUT HDH12(Optional) 6 Pin Power/Dome Light Harness (P/N 112-4270) 5 Pin AV Input Harness (P/N 112-4259) 5 Pin AV Output Harness (P/N 112-4260) NOTE: The Hidden 24 Pin connector only allows connection of either optional SmartStream Module (WM1) or HD/USB Extension harness (HDH12).
-
Page 19: Installing The Unit Video System-Mounting The Unit
Installing the Unit Video System-Mounting the Unit Installing the System 1. Make all electrical connections. 2. Attach the Unit to the mounting bracket using four M5 screws. CAUTION: The M5 screws are supplied in three different lengths (10mm, 20mm and 40mm) to facilitate proper installation. -
Page 20: Appendix A - Removing The Screen Back Cover
Appendix A - Removing the Screen Back Cover This section is intended for situations where the color of the Shroud, Screen Cover and Trim Ring need to be changed after the unit is setup for installation. NOTE: Work on a soft surface to avoid damaging the plastic. Removing the Screen Back Cover 1. -
Page 21: Appendix A - Removing The Trim Ring And Shroud
Appendix A - Removing the Trim Ring and Shroud Removing the Trim Ring 1. Remove the Trim Ring screws ((8) M3 x 5mm screws). NOTE: Do not Discard Screws! These screws are used to attach the new Trim Ring. 2. Remove the Trim Ring and discard. (8)... -
Page 22: Appendix B - Installing The Optional Thick Trim Ring
Appendix B - Installing the Optional Thick Trim Ring This section covers only special installation considerations for the optional thick trim ring installation. consideration for when an installation requires use of our Optional thick trim ring. Important NOTES before installing the thick trim ring: • There should be a gap between the headliner and the outer flange of the video monitor. -
Page 23: Appendix C - Installing The Optional Smartstream Module (Wm1)
Appendix C - Installing the Optional SmartStream Module (WM1) This section is intended as an installation guide to connect the WM1 Module to the Unit NOTE: The WM1 Module is sold separately and is supplied with its own instruction manual. Installing the WM1 Module Turn the DVD Player over on a surface with protective covering to prevent scratches. -
Page 24: Troubleshooting
Troubleshooting SYMPTOM: REMEDY: No power at video monitor • Verify +12 VDC on the Red wire at 6 Pin Power/ Dome Light Harness behind the video monitor. Verify a ground connection with a continuity test from a known good ground to the black wire. Power but no video or sound • Verify that the Source is on and playing back compatible media content. - Page 25 Troubleshooting SYMPTOM: REMEDY: FM Transmitter does not work • Check if radio is ON and in FM mode. • Check that radio is tuned to the same frequency as the unit is set to. • Select another FM channel. • Reposition the Unit Wireless FM antenna for better reception.
- Page 28 © 2016 Voxx Electronics Corp.,180 Marcus Blvd Hauppauge, NY 11788 730-099...
This manual is also suitable for:
Movies2go mtg13uhd